Interference effect of two equal‐sized square cylinders in tandem arrangement: With planar shear flow

Numerical simulations have been performed for flow past two equal‐sized square cylinders in tandem arrangement subjected to incoming planar shear flow. Effect of L/d ratio and the shear parameter has been studied. The range of L/d ratio (ratio of center‐to‐center distance (L) to cylinder width (d)) is varied from 2 to 7 and the non‐dimensional shear parameter (K) is varied from 0.0 to 0.4 in steps of 0.1. For all the cases the Reynolds number (Re) based on centerline velocity and cylinder width is fixed at 100. The results are compared with that of isolated square cylinder with uniform flow. Strouhal number decreases with increasing shear parameter. There are more than one shedding frequency at high shear parameters and L/d ratios. The mean drag coefficient is decreased with shear parameter and lesser than that of the single cylinder. The root mean square (RMS) value of both lift and drag coefficients is higher for the downstream cylinder for all values of shear parameter. With increasing L/d ratio, for both lift and drag, the RMS value increases and then decreases for upstream cylinder, whereas it continuously increases for the downstream cylinder. The stagnation point is moved towards the top leading edge with increasing shear. The critical L/d ratio, which is defined as the distance between two cylinders, beyond which the vortex shedding from the upstream cylinder occurs, decreases with increasing shear parameter. Copyright © 2007 John Wiley & Sons, Ltd.     

Power spectra and spatial pattern dynamics of a ring laser

Experimental measurements of power spectra of a single longitudinal and transverse mode ring dye laser are presented that reveal the critical slowing down of the laser near threshold. External pump noise serves as a probe of the frequency response of the dye laser. Detailed comparisons of the spectral characteristics with computer simulations and an approximate analytic theory are given. The dynamics of spatial pattern formation in a multimode dye laser is examined through measurements of first-passage-time distributions. A comparison of the experiments with computer simulations based on a simple theoretical model of the two-mode laser shows qualitative agreement. These measurements indicate that there are a variety of complex phenomena associated with the transverse mode pattern formation dynamics that need to be addressed theoretically and studied further experimentally.     

断裂过程区D—B模型的叠加原理和截荷修正法

提出分析中心裂纹板剪切断裂的断裂过程区D－B模型的叠加原理，考虑了压剪断裂的摩擦阻力和体现有限权宽影响的载荷修正，以非常简便的方法推导出计算断裂过程区长度和位移的公式。     

On the theory of the shear-induced isotropic-to-nematic phase transition of side chain liquid-crystalline polymers

The shear-induced isotropic-to-nematic phase transition of side chain liquid-crystalline polymers is studied theoretically. A modification of the previous models of main-chain liquid crystals to the case of side chain liquid-crystalline polymers is proposed. Orientational and rheological properties of the model are studied in plane-shear flow. Predictions of the present model agree qualitatively with experimental results (Pujolle-Robic, Noirez in Nature 409:167, 2001).     

Flow past a cylinder: shear layer instability and drag crisis

Flow past a circular cylinder for Re=100 to 10⁷ is studied numerically by solving the unsteady incompressible two‐dimensional Navier–Stokes equations via a stabilized finite element formulation. It is well known that beyond Re ～ 200 the flow develops significant three‐dimensional features. Therefore, two‐dimensional computations are expected to fall well short of predicting the flow accurately at high Re. It is fairly well accepted that the shear layer instability is primarily a two‐dimensional phenomenon. The frequency of the shear layer vortices, from the present computations, agree quite well with the Re^0.67 variation observed by other researchers from experimental measurements. The main objective of this paper is to investigate a possible relationship between the drag crisis (sudden loss of drag at Re ～ 2 × 10⁵) and the instability of the separated shear layer. As Re is increased the transition point of shear layer, beyond which it is unstable, moves upstream. At the critical Reynolds number the transition point is located very close to the point of flow separation. As a result, the shear layer eddies cause mixing of the flow in the boundary layer. This energizes the boundary layer and leads to its reattachment. The delay in flow separation is associated with narrowing of wake, increase in Reynolds shear stress near the shoulder of the cylinder and a significant reduction in the drag and base suction coefficients. The spatial and temporal power spectra for the kinetic energy of the Re=10⁶ flow are computed. As in two‐dimensional isotropic turbulence, E(k) varies as k^?5/3 for wavenumbers higher than energy injection scale and as k^?3 for lower wavenumbers. The present computations suggest that the shear layer vortices play a major role in the transition of boundary layer from laminar to turbulent state. Copyright © 2004 John Wiley & Sons, Ltd.     

Scission induced by circular shear and heat conduction in an elastomeric cylinder

Constitutive equations for the thermo-mechanics of elastomeric materials generally assume that they do not undergo microstructural change. A constitutive theory is discussed here which accounts for such changes arising from continuous scission of macromolecular junctions of elastomeric networks due to deformation and high temperatures and the subsequent cross-linking of molecules into new networks with new reference states. The total stress is the superposition of the stresses in the remainder of the original network and in each subsequently formed network. Each network acts as a temperature-dependent non-linear elastic material. The interaction of this material response with inhomogeneous deformation and temperature fields is studied for finite circular shear of a cylinder. Numerical results illustrate how the mechanical response of the cylinder depends on the temperature dependence of both the scission–cross-linking process and the properties of the elastic networks.     

Pure Shear – A Footnote

A result on pure shear provides the motivation for the determination of some new general results relating real second order Cartesian tensors.      

Shear buckling modes of cylindrical sandwich shells under external pressure, tension-compression of bearing layers with unequal forces, and inhomogeneous across-the-thickness temperature

Equations are set up for describing, in a correct statement and with an accuracy sufficient in actual practice, the shear buckling modes (BMs) of cylindrical sandwich shells with a transversely soft core of arbitrary thickness. Based on them, solutions are obtained to a number of problems on the buckling instability according to shear modes under some force and thermal loadings. It is found that the BMs occur in the shell along the circumferential and axial directions if, in the precritical state, a normal compressive stress arises in the transverse direction. It is shown that this condition is fulfilled in the following cases: in axial tension of the shell with unequal forces applied to the end faces of bearing layers (the parameter of critical load is maximum if the tensile forces are equal); under external (internal) pressure; on cooling the outer and heating the inner layers. The results obtained are presented in the form of simple analytical formulas for determining the corresponding critical parameters of the force and thermal actions.Translated from Mekhanika Kompozitnykh Materialov, Vol. 41, No. 1, pp. 37–48, January–February, 2005.